|
|
SureFire's Helmet light HL1-D-TN 头盔灯
2/6/07 - SureFire's Helmet light was introduced more than a year ago at the 2006 SHOT show. Very unconventional in appearance, it was one of the 'must have' gadgets when it
first came out. SureFire has improved on the original helmet light, and also developed a MOLLE adaptor for the helmet light to further increase its utility.
surefire 的头盔灯是2006年shot show上推出的。有着非凡的外观，是一个“必须”要拥有的小玩意。surefire已经升级了这个灯，并且设计了一个MOLLE夹拓展它的适用范围。
The helmet light itself is made of flat-dark earth coloured glass filled nylon and neoprene. The watertight battery compartment holds one SF123A battery and is O-ring sealed.
The cap has a rubber lanyard to prevent loss. At the front of the light are five 5mm LEDs. The colour of the LEDs depends on the particular model (there are four different
available configurations). There are two rubber covered toggle switches at the rear of the light. When the Helmet light was first introduced, these toggle switches were
exposed, and could be accidentally turned on if bumped, or when the helmet was stored inside a bag. The 'Gen 2' Helmet light has a hard plastic shroud which protects the two
toggle switches from accidental activation. Molded on the shroud are symbols which show what the different switch positions do. The LEDs are turned on with the upper switch -
the middle position is off, and flipping it up turns on the primary lights, and toggling it down turns on the secondary colour. The lower toggle switch turns on the IR IFF
light on the side, which is a 3mm IR LED beacon which flashes about once a second. Pressing the round button on the side cycles through the intensity of the primary and
secondary lights - low, medium and high.
头盔灯用的是哑光的土色的，混合玻璃纤维、尼龙和氯丁橡胶制造的。不透水的电池藏可容乃一节SF123A电池和一个o型防水圈。电池帽上有橡胶固定带方式丢失。在前面，有5个5毫米的led。led的颜
色是由型号决定的（总共有四种排列组合方式）有两个橡胶扣在手电后面。当头盔灯第一次被介绍的时候，这个按钮是暴露在外的，很容易被误碰或者头盔放在包里面的时候被启动。Gen 2灯有一个硬
质塑料壳子防止这两个开关被意外启动。朝上扳开关是打开，中间是关闭，轻按将打开主灯，朝下扳将打开附属灯。另外一个开关可以打开红外，这个3毫米的红外灯一秒一闪。按在上面的按钮可以对
主灯和次灯的低中高三个档位进行循环切换。
The helmet mount is over molded in neoprene for a non-slip surface. It attaches to most ballistic helmets on the left-hand side.A metal bracket clamps to the rim of the helmet
and is snugged down with two screws on the side and a set screw on the bottom. It's very secure and does not move. The light slides onto the mount, and locks in place.
Depressing a small lever unlocks it and allows it to be removed. It weighs only 3.1 oz with battery.
这个头盔架采用防滑表面，适用于大多数ballistic helmets的左侧面。用一个金属夹夹注头盔边缘，调整到合适的位置，拧紧两个螺栓。很牢靠，不会移动。把灯本体在支架上滑动并锁定。将锁定钮
按下一点就可以方便的拿下来。连电池只有3.1盎司重。
The model shown here is the HL1-A-TN, with white primary LEDs and blue secondary LEDs. At the high setting, the white LEDs last 6 hrs and output 19.2 lumens, while at the low
setting they last for 48 hrs at 1.4 lumens. VIsit the SureFire link above for more specifications and information on the other settings. The LED is bright enough for close-up,
general purpose tasks, and the blue setting is a more NV-friendly colour. The tertiary IRR led, when turned on, emits a barely perceptible red glow when it flashes.
这个展示型号是HL1-A-TN，有白色主灯和蓝色附灯。最高模式工作状态下，白色led可以提供6小时19.2流明的输出，如果是强度输出，将提供1.4流明的48小时输出。具体的设定和说明请参考信息请查
询官方链接。这个亮度已经能适应一般的使用情况，蓝色的灯光是一个很适合夜间使用的颜色。红外灯发出的灯光，肉眼几乎看不到。
The SureFire Z71 MOLLE adapter for the helmet light utilizes two columns of PALS webbing. Constructed of glass-filled nylon, the adapter securely mounts to any MOLLE webbing,
with little or no sag, as the thickness of the 'feet' take up any slack in the webbing. The two feet are slipped into the two columns of PALS where they lock in place. The
mounting head has a spring-loaded detent, and pivots to five pre-set angles - from stowed (down) to past horizontal. The helmet light is installed and removed with the same
lever as on the helmet mount. Shown below is the HL1-D-TN variation of the helmet light, with three yellow-green LEDs for the primary light, and two IR LEDs as the secondary.
Unlike the tertiary IFF LED on the side which you can visually confirm is operating by looking for the almost imperceptible red glow when it flashes, I could not perceive
anything from the IR LEDs without night vision.
surefire z71 MOLLE配件用了两个专用于带状物固定的柱型卡子。用添加玻璃纤维的尼龙制造，这个卡子可以安全的适用于任何MOLLE带，一点点的松弛，一点点的下垂，松紧度正合适。两个柱型卡子
固定在两截带子上固定住。柱型卡有一个带有弹性的锁定扣，将从水平面到垂直面分割成五个可固定的角度。头盔灯和这个MOLLE卡子的结合分解方式和头盔架是一样的。HL1-D-TN这个型号，有三个黄
绿色led作为主灯，两个红外灯作为附灯，两边的红外灯不带夜视仪啥也看不到。
The MOLLE adapter further increases the versatility of the SureFire helmet light and also provides a good place for storing it when not mounted on the helmet. Contact SureFire
for more information and availability.
这个ＭＯＬＬＥ带不光增加了这个头盔灯的使用范围，同时还解决了在不使用头盔时候的使用问题。更多的信息请参见网站。
[ 本帖最后由 bearsyy 于 2007-9-17 17:22 编辑 ] |
|
IP卡
狗仔卡
发表于 2007-9-17 16:32
微信
收藏
分享
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
楼主
发表于 2007-9-21 10:56
